特價

S4A感測互動擴充板 V1

NT$280

S4A感測互動擴充板 V1

S4A Sensor Board for Arduino主要設計給Arduino/Motoduino 或S4A初學者使用的一塊互動板,結合麥克風、按鍵開關、光源感測、滑桿式可變電阻、LED 、蜂鳴器等元件,以及四組RJ11的接頭可供外部連接其他裝置或元件,如溫濕度感測器、土壤濕度感測器等。另外預留一個藍芽孔位給需要無線傳輸的使用者。可利用此無線傳輸跟Android手機或電腦溝通。AIS板子上也預留六根數位腳位給其他需要外部電源的裝置使用,例如連接多個伺服馬達。RJ11端可接至少十米長的電話線連接感測器。

描述

技術規格

1. 四個RJ11接頭容易外接其他裝置(D2/D3, A3,A4,A5)

2. 一個一公分大小的按鍵開關(D2)

3. 一個蜂鳴器(D9)

4. 一個麥克風( A2)

5. 兩顆 LED 顯示,一顆為紅色(D10),一顆為綠色(D11)

6. 一個滑桿可變電阻(10K),有效行程65mm.(A0)

7. 一個光感測元件(A1)

8. 預留一個藍芽孔位(UART)

9.尺寸: 8 x 8.3 cm

商品內容

§ S4A Sensor Board 1個

程式範例

/*

S4A sensor board testing sketch

Input components: Light sensor, microphone, VR slide, Button

Output components: Red Led, Green Led, Buzzer(speaker)

Author: https://motoduino.com

Description: S4A sensor board is suitable for arduino.

*/

// INPUT PIN

const int VR_InPin = A0; // Analog input pin that the potentiometer is attached to

const int CDS_InPin = A1; // Analog input pin that Light Sensor is attached to

const int MIC_InPin = A2; // Analog input pin that the microphone is attached to

const int Button_InPin = 2; // Analog input pin that the microphone is attached to

// OUTPUT PIN

const int Ledred_OutPin = 10; // Analog output pin that the RED LED is attached to

const int Ledgreen_OutPin = 11; // Analog output pin that the GREEN LED is attached to

const int Buzzer_OutPin = 9; // Analog output pin that the Buzzer is attached to

int sensorValue = 0; // value read from the pot

int outputValue = 0; // value output to the PWM (analog out)

int length = 15; // the number of notes

char notes[] = “ccggaagffeeddc “; // a space represents a rest

int beats[] = { 1, 1, 1, 1, 1, 1, 2, 1, 1, 1, 1, 1, 1, 2, 4 };

int tempo = 300;

// variables will change:

int buttonState = 0; // variable for reading the pushbutton status

char val; // variable to receive data from the serial port(bluetooth)

void playTone(int tone, int duration) {

for (long i = 0; i < duration * 1000L; i += tone * 2) {

digitalWrite(Buzzer_OutPin, HIGH);

delayMicroseconds(tone);

digitalWrite(Buzzer_OutPin, LOW);

delayMicroseconds(tone);

}

}

void playNote(char note, int duration) {

char names[] = { ‘c’, ‘d’, ‘e’, ‘f’, ‘g’, ‘a’, ‘b’, ‘C’ };

int tones[] = { 1915, 1700, 1519, 1432, 1275, 1136, 1014, 956 };

// play the tone corresponding to the note name

for (int i = 0; i < 8; i++) {

if (names[i] == note) {

playTone(tones[i], duration);

}

}

}

void setup() {

// initialize serial communications at 57600 bps:

Serial.begin(57600);

pinMode(Ledred_OutPin, OUTPUT);

pinMode(Ledgreen_OutPin, OUTPUT);

pinMode(Buzzer_OutPin, OUTPUT);

// initialize the pushbutton pin as an input:

pinMode(VR_InPin, INPUT);

pinMode(CDS_InPin, INPUT);

pinMode(MIC_InPin, INPUT);

pinMode(Button_InPin, INPUT);

}

void loop() {

buttonState = digitalRead(Button_InPin);

// check if the pushbutton is pressed.

// if it is, the buttonState is HIGH:

if (buttonState == HIGH) {

// turn LED on:

digitalWrite(Ledred_OutPin, HIGH);

// Buzzer testing

for (int i = 0; i < length; i++) { if (notes[i] == ‘ ‘) { delay(beats[i] * tempo); // rest } else { playNote(notes[i], beats[i] * tempo); } // pause between notes delay(tempo / 2); } digitalWrite(Ledred_OutPin, LOW); } // Test VR // read the analog in value: sensorValue = analogRead(VR_InPin); // map it to the range of the analog out: outputValue = map(sensorValue, 0, 1023, 0, 255); // change the analog out value: analogWrite(Ledred_OutPin, outputValue); // Light sensor testing // read the analog in value: sensorValue = analogRead(CDS_InPin); // map it to the range of the analog out: outputValue = map(sensorValue, 0, 1023, 0, 255); // change the analog out value: analogWrite(Ledgreen_OutPin, outputValue); // microphone sensor testing // read the analog in value: sensorValue = analogRead(MIC_InPin); // map it to the range of the analog out: if(sensorValue > 200)

{

outputValue = map(sensorValue, 0, 1023, 0, 255);

// change the analog out value:

analogWrite(Ledred_OutPin, outputValue);

}

// print the results to the serial monitor:

// Serial.print(“sensor = ” );

// Serial.print(sensorValue);

// Serial.print(“\t output = “);

// Serial.println(outputValue);

// wait 10 milliseconds before the next loop

// for the analog-to-digital converter to settle

// after the last reading:

delay(10);

}

接線範例

可直接把S4A Sensor Board 底下排針對準Arduino 腳座插上去即可。藍牙模組(選購)可以直接插在藍牙預留腳座!